Dallas, TX · Open 7 AM to 10 PMCall: (469) 264-8319

Garage Door Opener Installation

Belt, chain and wall-mount openers matched to the door, the ceiling and the noise you can live with.

Garage door opener installation means fitting a new unit to a door that already balances, then setting its limits and safety sensors. Chain-drive openers use a metal chain and are durable but louder; belt-drive models use a rubber belt and run quieter; screw-drive units turn a threaded rod; and a wall-mount, or jackshaft, opener sits beside the door and leaves the ceiling clear. Clopay and LiftMaster describe these trade-offs, and wall-mount units usually cost more up front.

An opener cannot fix a door that is out of balance, so we test the springs first. Then we mount the rail or the wall unit, wire the photo-eyes no more than six inches above the floor, add the wall button, program the remotes and set the travel and force limits. A backup reversing system, normally photo-eyes, became mandatory on new openers in 1993, and DASMA says an opener without one should be replaced.

We test the contact reversal with a 2x4 and the photo-eyes before we leave.

When an Opener Is Due for Replacement

  • From the kitchen you can hear the chain rattle every time it runs.
  • Nothing sits at floor level by the door tracks: no safety eyes at all.
  • The door crawls, or quits somewhere in the middle of its travel.
  • The remote only works from the end of the driveway now.
  • You would rather have storage space than a motor hanging in the middle.
  • The chain slaps the rail, or the rail itself sags under the motor.

Summer Heat and Opener Age

Heat and age are what we weigh when an opener is replaced here. Love Field averages about 108 days a year at 90°F or higher, and an opener motor works inside that heat in an attached garage. Clopay notes that screw-drive openers can be more sensitive to extreme temperature swings, so we weigh the drive type against how the garage is exposed. In a house built in the 1970s or 1980s, an opener that is still original predates the 1993 rule, so replacing it is also the first time the door gets photo-eyes.

Technician setting up the wall control of a new opener
Technician on a yellow ladder at the top of a white panel door
Technician reaching up to the top roller of a white garage door

What Installation Day Looks Like

Step 1

Tell us about the door and garage

A person answers and asks about the door size, the current opener, the ceiling height and whether the garage is attached. We plan the visit around that.

Step 2

Balance test and exact quote

The crew checks the door's balance and track, measures the headroom and recommends a drive type. The price for the unit and the fitting is set out in full before we unbox anything.

Step 3

Install and program

We mount the opener, wire the wall control and photo-eyes, program the remotes and set the limits and force for your door.

Step 4

Safety test and walk-through

We test contact reversal with a 2x4, test the photo-eyes, and show you the release handle and the 30-day safety check.

Opener Installation Prices

Diagnostic Service Call $0 with a completed repair
$0

Figures shown are where each job starts. Your door's weight, the parts it takes and the grade of hardware set the final number, which you see and approve at the house first.

Get My Exact Quote All prices →

Choosing a New Opener

Belt, chain or screw drive: which one suits our house?
Chain drive is durable and costs less but is louder, belt drive is quieter, and screw drive has fewer moving parts but can be more sensitive to temperature swings, according to Clopay and LiftMaster. LiftMaster positions belt drive for attached garages and chain drive for heavy, frequently used doors, and we choose by the door and the garage.
Is it worth paying more for a motor that mounts on the wall?
A wall-mount, or jackshaft, opener is worth considering when headroom is short or the ceiling is needed for storage, because it mounts beside the door and operates quietly. Clopay notes the main trade-off is a higher upfront cost. It needs a torsion shaft and side room beside the door, which we confirm on site.
Our opener dates from before 1993. Does it have to go?
DASMA recommends replacing openers made before 1993, because the rules for external entrapment protection, such as photo-eyes, were added that year, according to the Consumer Product Safety Commission. An opener without sensors can leave a closing door without a second way to stop. We check the label and test the reversal before we advise.
Can a brand-new opener run an older garage door?
Only if the door is balanced and moves freely, because an opener is not built to lift a door. We test the balance first. A door with a worn spring or a bound track needs repair before an opener goes on, or the new opener will strain the same way the old one did.
What is included when you install a new opener?
We mount the opener, wire the photo-eyes and wall button, program the remotes, set the travel and force limits, and test the contact reversal with a 2x4. We also show you the red release handle, which UL 325 requires to be red and easy to tell apart, and which DASMA says belongs no more than six feet above the floor.
Contact Us

Reach the Sherry Lane Garage Door Desk

Describe the noise, the stuck spot or the part that snapped, and a technician from our Preston Center office phones you back. Jobs start at the figures on the price list; the number for your own door is settled at the house, before anything comes apart.

Reunion Garage Door Repair Expert of Sherry
5956 Sherry Ln 20th Floor
Dallas, TX 75225

Phone: (469) 264-8319
Email: info@reuniongaragedoorrepairsherry.com
Hours: Open 7 AM to 10 PM, 7 days a week

Get My Free Estimate ☎ Call (469) 264-8319

Your name and number are used only to return your call, as set out in our Privacy Policy.

☎