Dallas, TX · Open 7 AM to 10 PMCall: (469) 264-8319

Garage Door Track Repair

Bent, loose and out-of-plumb tracks straightened or replaced, with the brackets re-anchored.

Garage door track repair realigns or replaces the steel rails that guide the rollers. The vertical tracks on each side are fastened to the jamb with brackets, curve through a radius at the top and join horizontal tracks that hang from the ceiling. DASMA notes that the horizontal track rises slightly, which helps start the door downward and helps maintain cable tension. When any part of that path is bent, loose or out of plumb, the rollers bind or jump out, and the door scrapes, shakes or stops.

We check the track for plumb and spacing, look for loose jamb brackets and stripped fasteners, and measure how far each roller sits from the track wall. A slightly bent rail can be straightened; a creased one is replaced. We secure the door before loosening anything, because the springs and cables stay under tension.

Afterward we balance the door and run the opener through full travel.

Signs the Track Is Out of Line

  • There is a metal-on-metal scrape along one side only.
  • The rollers on one side ride hard against the track.
  • The door halts on the way down for no clear reason.
  • One side of the door reaches the floor before the other.
  • A gap has opened between the closed door and the jamb.
  • A section of track is kinked or has pulled away from the wall.

Blackland Clay That Moves the Slab

The Texas State Historical Association describes Dallas County as primarily heavy Blackland Prairie, and Texas A&M AgriLife Extension says the clay soils of the Blackland Prairie swell when wet and shrink when dry. In our experience those cycles move slabs and door frames by small amounts, and a jamb that shifts even a fraction of an inch pulls a vertical track out of plumb. That is why tracks here can need realigning on houses with no impact damage. We check the opening for plumb before we reset the rail, because a track set straight to a crooked jamb will bind again.

Technician in safety glasses spraying lubricant on the vertical track
Technician on a ladder adjusting the side track of a raised door
Racks of steel track, springs and door hardware in a parts room

How We Straighten a Track

Step 1

Tell us where it rubs

A person answers and asks where the door scrapes or sticks and whether it still moves. That tells us which side and which section of track to look at first.

Step 2

Inspect and quote

The crew checks the track for plumb, spacing and creases, the jamb brackets and the rollers. We give the exact quote on site before any work starts.

Step 3

Realign or replace

We secure the door and work around the spring tension. We straighten a repairable rail, replace a creased one, and tighten or relocate loose brackets.

Step 4

Test the travel

We run the door through full travel, check the balance and confirm that nothing rubs. Then we test the opener's safety reversal.

Track Repair Prices

Track Repair & Off-Track Door per door
From $150
Diagnostic Service Call $0 with a completed repair
$0

Figures shown are where each job starts. Your door's weight, the parts it takes and the grade of hardware set the final number, which you see and approve at the house first.

Get My Exact Quote All prices →

Track Questions

Why would the door rub the track on only one side?
One-sided rubbing usually comes from a vertical track that has moved out of plumb, a loose jamb bracket, or a worn roller riding hard on one side. A door that is out of balance can also pull to one side. We check plumb, brackets and rollers before we straighten anything.
Is it a good idea to bend a track back into line yourself?
It is not advisable. The door and its springs are under load, and DASMA says repairs and adjustments to door parts belong to a trained door systems technician. Hammering a track can crease it, which makes the bind worse. Stop using the door once it binds.
What makes a door stop partway on its way down?
Common causes are a roller binding in a bent section of track, a cable that has gone slack, or the opener's down limit set too high. Clear the sensor beam first. If the track is visibly bent or a roller is out of its channel, stop using the door.
Why do track brackets work loose from the wall?
Fasteners work loose from vibration and from movement of the wall or slab, and wood jambs can split. DASMA's checklist asks whether all hardware parts are securely and appropriately attached. We replace stripped fasteners with longer ones or move the bracket to solid wood.
Contact Us

Reach the Sherry Lane Garage Door Desk

Describe the noise, the stuck spot or the part that snapped, and a technician from our Preston Center office phones you back. Jobs start at the figures on the price list; the number for your own door is settled at the house, before anything comes apart.

Reunion Garage Door Repair Expert of Sherry
5956 Sherry Ln 20th Floor
Dallas, TX 75225

Phone: (469) 264-8319
Email: info@reuniongaragedoorrepairsherry.com
Hours: Open 7 AM to 10 PM, 7 days a week

Get My Free Estimate ☎ Call (469) 264-8319

Your name and number are used only to return your call, as set out in our Privacy Policy.

☎